Changing a two-handle shower valve doesn’t have to be difficult. It is actually quite easy. There are some precautions that you should take before getting started, but in general, it is something that anyone can do with the right tools and instructions.
Today we will show you steps to replace two handle shower valves step by step so when the time comes for you to change yours, you’ll know exactly what to do. It’s not as difficult as it may seem to change a two-handle shower valve.
Steps To Replace Two Handle Shower Valves
First thing’s first, you will need some tools. Here is what you will need:
- Soldering torch
- Slip-joint pliers
- Conversion plate
- 4-in-1 screwdriver
- Pipe fittings
- New shower valve
Now that you have the necessary tools, it is time to get started. But before we do, there are a few things that you need to know before you begin.
Turn off Water Supply
Turn off the water supply in the very beginning. This can be done by turning off the valve that is located under the sink. Once you have turned it off, you can go ahead and start working on the shower valve.
You should never start working on the shower valve itself before turning off the water supply. Once the water is turned off, you can safely proceed with the installation.
If you are not sure where the valve is located, it is a good idea to ask someone for help. It may be in a different location depending on your home. Once you have found it, turn it off and then move on to the next step.
Remove Handles and Stems
The next step is to remove the handles and stems from the old shower valve. This can be done by using a screwdriver. Once they are removed, you should set them aside so that you can use them later during the installation process.
Start by removing the screws that are located on the top of each handle. Once they are removed, you can pull the handles straight off. Be careful not to break them.
Next, remove the screws from the stems. There is one screw at the top and one at the bottom. Once they are removed, you can pull the stems straight out. Again, be careful not to break them.
Now that both of these pieces have been removed, you can move on to the next step.
Take out The Faulty Valve
The faulty valve must then be removed. This can be done by using a jigsaw. Be careful not to cut into the piping while you are doing this. If you are not comfortable doing this yourself, you may want to ask someone for help.
Do this with the power turned off and the water supply shut down. You don’t want to risk anything electrically or environmentally dangerous happening because you made a mistake.
Once you have removed it, set it aside so that you can use it later during the reassembly of the new shower valve.
Now that both faulty valves are out, we move on to installing the new one.
Replace the Faulty Valve and Shower Faucet Parts
The next stage is to repair any broken shower valve or faucet components. This can be done by following these simple steps:
First, take the new valve and place it in the hole that you just cut out. Make sure that it is in the correct position before moving on.
Next, put the stems back into place and screw them in tightly. Be careful not to over-tighten them or you may damage them.
Now, put the handles back on top of the stems and screw them in place. Again, make sure that they are tight so that they don’t come loose later on.
Once everything is in place, we reattach the conversion plate to finish up the installation process. This can be done by using a screwdriver to secure the conversion plate in place.
Now that everything has been installed, it is time for you to turn your water supply back on and test out your new shower valve.
If there are any leaks or problems with the installation process, don’t hesitate to contact someone who can fix them properly so they do not cause damage later down the road.
Switch on the water supply
After that, turn on the water supply. This can be done by following these simple steps:
First, turn your faucet until you are able to get a good stream of water coming out from it. If there isn’t any water that comes out at all this means that you have not turned the valve back on properly and will need to try again.
Once you have taken care of this problem, go ahead and test out your new shower valve in order to make sure everything has been installed correctly.
If there aren’t any leaks or problems with the installation process, then congratulations! You now know how to change a two-handle shower valve without having to call in an expensive plumber!
If for some reason there are still problems with the installation process, then there is always a solution that you can attempt to fix them.
If none of these work and your shower valve still doesn’t function properly, you may want to call in a professional plumber for assistance instead.
Now that everything has been installed it’s time for you to turn on the water supply so we can test out our new shower faucet parts!
Changing a two-handle shower valve is not as difficult as it sounds. If you follow the steps to replace two handle shower valves that we have provided, then this task should be no problem for you to complete on your own.
Be sure to switch off your water supply and shut down any power before beginning so that there are no accidents waiting to happen. With just a screwdriver and jigsaw in hand, installing a new shower valve can take less than an hour.
So go ahead and get started with these simple steps today! Which of the above tasks did you struggle most with?
Let us know what tools or techniques worked best for you when changing out a faulty plumbing fixture in your home bathroom too! We would love to hear from our readers about their experience doing so.
I am a full-time professional architect who is passionate about all kinds of stuff design and construction. Now I share my advice and experience in the architecture and home improvement industries. In MAV SoHo I recommend the best shower heads to help you achieve your goals and simply get the job done at an affordable cost.