If you click on any link on MavSoho.com & decide to buy it, we may earn a small commission. Read More Here
The shower diverter is an important element of your home plumbing system. This part of your plumbing allows you to decide where the water goes in the shower – whether it will go into a bathtub or down the drain.
If you have a leaky one, you’re going to have some unpleasant and costly surprises later on. That’s why we’re going to walk you through how to repair your shower diverter with 6 easy steps.
How To Know If Shower Diverter Valve Is Broken?
Shower diverters are important plumbing pieces that help regulate where the water in your shower goes. If this part of the system is broken, it can lead to some costly and unpleasant surprises later on. To check if a problem with your shower diverter valve has occurred, take a look at these symptoms:
- Unable to turn off all hot water from the faucet or handle.
- Water going down drain when trying to fill the bathtub.
If you notice any of these problems happening in your home’s plumbing system, then you’re probably experiencing issues with your shower diverter valves. That means they need repair! Thankfully we have just the guide for how to fix them right here!
How to Repair Your Shower Diverter
Step 1: Turn off the water supply to your shower diverter valve. This can be done by turning off the shutoff valve that is located on or near it or unscrewing a hose from its inlet and outlet ends. Making sure there’s no pressure coming out of this part of the system will help you avoid any possible further harm while working with it.
Step 2: Remove all washers because they’re often damaged during repair attempts. You should also remove them before making repairs, as these pieces may have been worn down due to age and time, which could lead to future problems if not replaced now! If you don’t know how to do either of these steps, consult a plumber for help.
Step 3: Make sure that the valve is fully opened by pushing it up or down, depending on which way you want to direct water flow from your shower diverter valve.
Step 4: Locate the rubber washer where water will come out of and make a note of its location in relation to anything that might be holding it back, like a screw, nut, bolt, or any other part.
Step 5: Put this new washer over the top of the one that’s there now so when you tighten things down again, they’ll hold each other tightly in place with no risk for future breakage! You can also try double-checking everything after tightening them just as an added measure before restarting your water supply!
If these steps have helped repair your shower diverter valve, then your water should have a steady flow coming out of the spout and continue on into either the bathtub or down the drain. If not, you might need to call in an expert plumber for help!
How To Replace a Shower Diverter Valve
If your shower diverter valve is broken, the best way to fix it will be by replacing it. This can be done in as little as an hour and with just a few easy steps that are outlined below!
Step 1: Turn off the water supply at shutoff valves or unscrew one end of the hose from its other on both ends of the diverter valve.
Step 2: Remove all washers because they’re often damaged during repair attempts. They should also be removed before any repairs are made if you don’t know how either step works; otherwise, future problems may occur due to wear over time! Consult the plumber for help if needed.
Step 3: Open the new valve fully by pushing up or down depending on the direction of the pipe opening.
Step 4: Locate the rubber washer where water will come out of and make a note of its location in relation to anything holding it back, like a screw, nut, bolt, or any other part.
Step 5: Put a new washer over the old one so that everything is held tightly together with no risk for future breakage! Double-check after tightening just as an added measure before restarting your water supply if needed.
If these steps have helped replace your shower diverter valve, then you should be able to resume normal use without any problems occurring due to lack of repair.
If you found this article helpful on how to repair your shower diverter, please share it with your friends and family. We know that when a shower diverter gets clogged or broken, the last thing on one’s mind is how to fix it.
However, if left unrepaired for too long, water can leak through walls or ceilings, causing structural damage in addition to being an inconvenience.
Here are some different ways of repairing a shower diverter, so there is no need to call up a professional plumber you can just do it by yourself with a bit of plumbing idea. Which of these methods did you try?
I am a full-time professional architect who is passionate about all kinds of stuff design and construction. Now I share my advice and experience in the architecture and home improvement industries. In MAV SoHo I recommend the best shower heads to help you achieve your goals and simply get the job done at an affordable cost.